I haven't seen them in Borders, are they under fiction or non-fiction?Vanny wrote:I've access to a 50 tonne hydraulic press and the last stubborn bearing i had ont he BX i struggled to get out even after welding a few beads in and part cutting the fucker. Sometimes brute force needs to be bigger
I try to always go SKF but i cen get them sub trade prices from Borders so its win win.
- jonathan_dyane
- New Member
- Posts: 379
- Joined: 07 Apr 2008
- Location: Liverpool
Re: Rumble in my Jungle
Jonathan.
Working vehicle: 1986 Mercedes 190D 2.5
Broken: GS 1220 Estate, Tomos Noped several MZ's, David Brown 30D.
Working vehicle: 1986 Mercedes 190D 2.5
Broken: GS 1220 Estate, Tomos Noped several MZ's, David Brown 30D.
- docchevron132
- Bus Warrior
- Posts: 11929
- Joined: 10 Oct 2006
- Location: Sat with a hammer under 8666KGs of rust!
- Contact:
Re: Rumble in my Jungle
I've always just given them the bearing number for any bearing I've wanted. Never failed yet.Bx Bandit wrote: With SKF Doc do you just order by size? I'll have a look at the web in a bit.
the dude with the great XM wrote:I haven't seen them in Borders, are they under fiction or non-fiction?
1989 BX 17TD P2 Hybrid
1990 BX 16V It's got big hairy bollocks
1971 BL 350FG ambulance
1993 Dennis Lance 132 It's got mahooosive hairy bollocks!
Euthenasia, because enough's enough already.
1990 BX 16V It's got big hairy bollocks
1971 BL 350FG ambulance
1993 Dennis Lance 132 It's got mahooosive hairy bollocks!
Euthenasia, because enough's enough already.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
Hmmmm, the plot thickens.
Original point of thread was rumble from front n/s when cornering round a roundabout.
I changed the n/s drive shaft no change.
Initial investigation (at time of first post) showed wheel bearing ok.
Over time, the wheel bearing did fail with the usual hum-drum as you drove along.
I have today replaced n/s front wheel bearing using a press. The drive-along hum-drum is gone but the rumble when cornering a roundabout persists.
As all this started after I changed the diff, then I'm drawing the conclusion it must be related to the diff.
Either: The ZX diff is slightly different and causes some sort of mechanical interference when cornering (rumble not noticable in opposite cornering direction)
or the ZX speedo drive is different causing similar to above
or the bearing within the diff has gone.
Any thoughts chaps? The poignant question I suppose is why it only happens turning through a sweeping right at low-moderate speed (larger roundabouts taken at say 30 mph produce the same noise as smaller ones taken at 10mph)
Nothing is rubbing. The rumble is mechanical with a throbbing or rythmic 'touch'
Original point of thread was rumble from front n/s when cornering round a roundabout.
I changed the n/s drive shaft no change.
Initial investigation (at time of first post) showed wheel bearing ok.
Over time, the wheel bearing did fail with the usual hum-drum as you drove along.
I have today replaced n/s front wheel bearing using a press. The drive-along hum-drum is gone but the rumble when cornering a roundabout persists.
As all this started after I changed the diff, then I'm drawing the conclusion it must be related to the diff.
Either: The ZX diff is slightly different and causes some sort of mechanical interference when cornering (rumble not noticable in opposite cornering direction)
or the ZX speedo drive is different causing similar to above
or the bearing within the diff has gone.
Any thoughts chaps? The poignant question I suppose is why it only happens turning through a sweeping right at low-moderate speed (larger roundabouts taken at say 30 mph produce the same noise as smaller ones taken at 10mph)
Nothing is rubbing. The rumble is mechanical with a throbbing or rythmic 'touch'
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- Site Admin
- Posts: 7512
- Joined: 10 Oct 2006
- Location: BXProjectHQ
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
hark at you mr 'I've got the hump with my car' miserable bastard!
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- Site Admin
- Posts: 7512
- Joined: 10 Oct 2006
- Location: BXProjectHQ
Re: Rumble in my Jungle
Combine shite car, no life, endless days on the motorway, living in the UK and the twat festival that is Christmas, and there is no reason for anyone to be cheery
-
- GET OUT MORE
- Posts: 8744
- Joined: 01 Nov 2007
- Location: Wigan Lancs
- Contact:
Re: Rumble in my Jungle
I got up this morning and found that I was still breathing in and out
So I'm cheerful end of!!
Mind you I have a good car, have fucked the M/way drag off, am leaving the country next week, for 3 weeks in the snow
So I'm cheerful end of!!
Mind you I have a good car, have fucked the M/way drag off, am leaving the country next week, for 3 weeks in the snow
72... AND STILL ROCKIN..........around the world...... NOT in a chair yet
Now XBX And into HDI.....as well as other ...err.... things.
Now XBX And into HDI.....as well as other ...err.... things.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
/\ Fuck off you smug snow bound svenski toss pot!
Why have you no life Vanny? Bored mate?
Why have you no life Vanny? Bored mate?
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
- David
- Part of the decor
- Posts: 1102
- Joined: 29 May 2007
- Location: Lo-ca-tion: a place of settlement, activity, or residence; act of locating; state of being located.
Re: Rumble in my Jungle
Does it make any difference if you are on load or off load?Bx Bandit wrote:The poignant question I suppose is why it only happens turning through a sweeping right at low-moderate speed (larger roundabouts taken at say 30 mph produce the same noise as smaller ones taken at 10mph)
Buggered bearings and/or meshed gears will make very different noises when they are loaded or unloaded
... all landings are in fact controlled crashes, and any crash you can walk away from is a good landing. The definition of a good pilot is a man with the same number of landings as take-offs.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
no, don't think so. Seems more dependant on the 'outward' force you'd expect to be exerted to the n/s front wheel. i.e. speed related as opposed to accel/load related
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- GET OUT MORE
- Posts: 8744
- Joined: 01 Nov 2007
- Location: Wigan Lancs
- Contact:
Re: Rumble in my Jungle
We're back to wheels and tyres I'm thinking!!
72... AND STILL ROCKIN..........around the world...... NOT in a chair yet
Now XBX And into HDI.....as well as other ...err.... things.
Now XBX And into HDI.....as well as other ...err.... things.
- docchevron132
- Bus Warrior
- Posts: 11929
- Joined: 10 Oct 2006
- Location: Sat with a hammer under 8666KGs of rust!
- Contact:
Re: Rumble in my Jungle
/\ yep, I thought that too..
The ZX speedo drive is different yes, but that would cause a permenant and speed related noise, it would also not do it very long since it would chew it's own arse off in minutes..
Have you tried swopping the tyress front to rear, or even off the other car?
Vanny, you miserable bastard. Ignore xmas. I am. Jobbed.
Move to Stroud, then you can borrow my life, I dont want it. Jobbed.
Become a hobo like me, no motorway's. Jobbed.
Fucking simple really aint it!
The ZX speedo drive is different yes, but that would cause a permenant and speed related noise, it would also not do it very long since it would chew it's own arse off in minutes..
Have you tried swopping the tyress front to rear, or even off the other car?
Vanny, you miserable bastard. Ignore xmas. I am. Jobbed.
Move to Stroud, then you can borrow my life, I dont want it. Jobbed.
Become a hobo like me, no motorway's. Jobbed.
Fucking simple really aint it!
1989 BX 17TD P2 Hybrid
1990 BX 16V It's got big hairy bollocks
1971 BL 350FG ambulance
1993 Dennis Lance 132 It's got mahooosive hairy bollocks!
Euthenasia, because enough's enough already.
1990 BX 16V It's got big hairy bollocks
1971 BL 350FG ambulance
1993 Dennis Lance 132 It's got mahooosive hairy bollocks!
Euthenasia, because enough's enough already.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
fucking hobo, I like that.
i haven't tried swapping tyres about no, so I will try that next. But it sounds too mechanical and the tracking is ok.
I checked under it today, had the suspension on low and there is still play in the d/shaft, so that's not getting locked up.
No fouling of hand brake cables
There is some play where the n/s d/shaft goes into the diff housing, which made me think aha! Bearing. But there is similar (if not more) play on a diff and driveshaft setup I have on the garage floor, and there were no similar noises on that one.
You intruige me about the speedo drive Doc, how is it different?
What can happen when you exert on outward force like going round the roundabout??? My only thought on this was lower arm bushes but they are ok
i haven't tried swapping tyres about no, so I will try that next. But it sounds too mechanical and the tracking is ok.
I checked under it today, had the suspension on low and there is still play in the d/shaft, so that's not getting locked up.
No fouling of hand brake cables
There is some play where the n/s d/shaft goes into the diff housing, which made me think aha! Bearing. But there is similar (if not more) play on a diff and driveshaft setup I have on the garage floor, and there were no similar noises on that one.
You intruige me about the speedo drive Doc, how is it different?
What can happen when you exert on outward force like going round the roundabout??? My only thought on this was lower arm bushes but they are ok
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- GET OUT MORE
- Posts: 8744
- Joined: 01 Nov 2007
- Location: Wigan Lancs
- Contact:
Re: Rumble in my Jungle
Put car in high, jack up offending wheel, measure from ctr to outside of tyre in about 5 or 6 positions
They should all be within > 3 mm. If it is, it's not the tyre, so while it's up in the air, put lever back to normal, put a bar in the suspenders and press down. Then do the physical check again. 12 and 6 o'clock then 9 and 3.
If still no joy put in low and repeat previous. If all OK, make an appointment with a hearing specialist
They should all be within > 3 mm. If it is, it's not the tyre, so while it's up in the air, put lever back to normal, put a bar in the suspenders and press down. Then do the physical check again. 12 and 6 o'clock then 9 and 3.
If still no joy put in low and repeat previous. If all OK, make an appointment with a hearing specialist
72... AND STILL ROCKIN..........around the world...... NOT in a chair yet
Now XBX And into HDI.....as well as other ...err.... things.
Now XBX And into HDI.....as well as other ...err.... things.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
My car doesn't wear suspenders! Explain from the word normal again, cos I 'aven't a clue wot you mean!
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- GET OUT MORE
- Posts: 8744
- Joined: 01 Nov 2007
- Location: Wigan Lancs
- Contact:
Re: Rumble in my Jungle
Height control...., err Low, Normal and High.
Put a bar between the lower suspenders swivel joint and the body and push down.
Hold wheel top and btm feel for movement by rocking it back and forwards. Transfer hands to each side of the tyre. feel for movement again.
Drop suspenders into LOW and repeat the above.
A further thought. Whilst holding the wheel side to side, try pushing it away from you and pulling it toward you with both hands at the same time. If there is no movement anywhere there's nowt wrong with it mate, so get your ears checked
Put a bar between the lower suspenders swivel joint and the body and push down.
Hold wheel top and btm feel for movement by rocking it back and forwards. Transfer hands to each side of the tyre. feel for movement again.
Drop suspenders into LOW and repeat the above.
A further thought. Whilst holding the wheel side to side, try pushing it away from you and pulling it toward you with both hands at the same time. If there is no movement anywhere there's nowt wrong with it mate, so get your ears checked
72... AND STILL ROCKIN..........around the world...... NOT in a chair yet
Now XBX And into HDI.....as well as other ...err.... things.
Now XBX And into HDI.....as well as other ...err.... things.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
Nope, still don't get what you mean!
What am I testing for? Lower b/j is ok.
Wheel bearing is ok
Bushes I 'think' are ok but need to check
two previously good d/shafts exhibit same 'fault'
I promise you it's not my ears, Mrs Bandit hears it and Charlie has too. Interestingly, I'm pretty sure it's not the degree of steering that makes the noise, but the force applied. i.e. take a motorway sized roundabout and it'll make the same noise on say 1/6 lock at 30 mph as it does on 1/2 lock at 15 mph.
Every ounce of me would say wheel bearing, but it just ain't.
God damn stoopid cars...........
What am I testing for? Lower b/j is ok.
Wheel bearing is ok
Bushes I 'think' are ok but need to check
two previously good d/shafts exhibit same 'fault'
I promise you it's not my ears, Mrs Bandit hears it and Charlie has too. Interestingly, I'm pretty sure it's not the degree of steering that makes the noise, but the force applied. i.e. take a motorway sized roundabout and it'll make the same noise on say 1/6 lock at 30 mph as it does on 1/2 lock at 15 mph.
Every ounce of me would say wheel bearing, but it just ain't.
God damn stoopid cars...........
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- GET OUT MORE
- Posts: 8744
- Joined: 01 Nov 2007
- Location: Wigan Lancs
- Contact:
Re: Rumble in my Jungle
What I said covers more or less everything at the front end but I've heard noises before at different height settings.
Just a thought. I never had the inner end of the drive shaft out on any of my BX's. Is it a straight spline, or a tripode thingy like my picasso?
Just a thought. I never had the inner end of the drive shaft out on any of my BX's. Is it a straight spline, or a tripode thingy like my picasso?
72... AND STILL ROCKIN..........around the world...... NOT in a chair yet
Now XBX And into HDI.....as well as other ...err.... things.
Now XBX And into HDI.....as well as other ...err.... things.
- Bx Bandit
- GET OUT MORE
- Posts: 6641
- Joined: 16 Nov 2006
- Location: Somewhere I don't want to be...
Re: Rumble in my Jungle
Straight spline mate
....There he goes, one of God's own prototypes, a high powered mutant of some kind never even considered for mass production......too weird too live.....and too rare to die
-
- GET OUT MORE
- Posts: 8744
- Joined: 01 Nov 2007
- Location: Wigan Lancs
- Contact:
Re: Rumble in my Jungle
I doubt it's anything at that end then. They were always fine.
I think they brought the tripode in so you would have something to fix and take apart every time you have to change the inner boot.
I think they brought the tripode in so you would have something to fix and take apart every time you have to change the inner boot.
72... AND STILL ROCKIN..........around the world...... NOT in a chair yet
Now XBX And into HDI.....as well as other ...err.... things.
Now XBX And into HDI.....as well as other ...err.... things.